Arch and Specialty Machines
5 products. Displaying 1 to 5.
U.S. Concepts Model No.: FAS-LE
Arch Moulder
The FAS-LE universal arch moulder is an entry level machine for curved and straight mouldings. This heavy duty, affordable machine can consistantly cut curved profiles by using U.S. Concept's unique floating feed system that registers on the outside edge of the curved blank. It is equipped with two (2) axis spindle adjustment to easily and accurately match the cutter to the desired profile. The spindle adjustments and floating feed make cutting irregular and straight profiles a breeze. MADE IN AMERICA.
Call (801)498-7891
Details: FEATURES: Max. profile width - 5"; Max. cutter diameter - 6.5"; Max.. material height - 4-1/4"; Spindle motor - 5HP; adjustable feed speed - 0 to 30 FPM; floating feed system with five (5) powered feed rolls; spindle tilt - 52 Deg.; wired for 230/3/60.
Additional Info: FEATURES: Max. profile width - 5"; Max. cutter diameter - 6.5"; Max.. material height - 4-1/4"; Spindle motor - 5HP; adjustable feed speed - 0 to 30 FPM; floating feed system with five (5) powered feed rolls; spindle tilt - 52 Deg.; wired for 230/3/60.
U.S. Concepts Model No.: FAS-LX
Arch Moulder
The FAS-LX universal arch moulder is an medium duty machine for curved and straight mouldings. This heavy duty, affordable machine can consistantly cut curved profiles by using U.S. Concept's unique floating feed system that registers on the outside edge of the curved blank. It is equipped with two (2) axis spindle adjustment to easily and accurately match the cutter to the desired profile. The spindle adjustments and floating feed make cutting irregular and straight profiles very easy. MADE IN AMERICA.
Call (801)498-7891
Details: FEATURES: Max. profile width - 5"; Max. cutter diameter - 6.5"; Max.. material height - 4-1/4"; Spindle motor - 5HP; adjustable feed speed - 0 to 30 FPM; floating feed system with five (5) powered feed rolls; spindle tilt - 52 Deg.; wired for 230/3/60.
Additional Info: OPTIONS: 460/3/60 electrics; 575/3/60 electrics; additional hold down rolls; locking fixture for true Radii; straight run fences; straight run feeder; 48" X 30" cast iron table.
U.S. Concepts Model No.: FAS-HD
Arch Moulder
The FAS-HD universal arch moulder is a heavy duty machine for curved and straight mouldings. This heavy duty, affordable machine can consistantly cut curved profiles by using U.S. Concept's unique floating feed system that registers on the outside edge of the curved blank. It is equipped with two (2) axis spindle adjustment to easily and accurately match the cutter to the desired profile. The spindle adjustments and floating feed make cutting irregular and straight profiles a breeze. This machine has been designed to accomodate moulding heads straight from the moulder. MADE IN AMERICA.
Call (801)498-7891
Details: FEATURES: Spindle diameter - 1-1/2" or 35mm; Max. profile width - 8"; Max. cutter diameter - 7.75"; Max.. material height - 4-1/4"; Spindle motor - 10 HP; adjustable feed speed - 0 to 30 FPM; floating feed system with five (5) powered feed rolls; spindle tilt - 52 Deg.; 49" X 31" cast iron table; wired for 230/3/60.
Additional Info: OPTIONS: 460/3/60 electrics; 575/3/60 electrics; additional hold down rolls; locking fixture for true Radii; straight run fences; straight run feeder; 1-13/16" spindle diameter.
HERSAF
DENTIL MOULDING MACHINE
The Dentil Molding Machine can be set for either single- or dual-cut dentil molding. The Dentil Molding Machine operates using mechanical and air logic technology. It has a steel framework designed with an impact valve to reduce machine stress. Each machine comes equipped with two 8" blades designed to deliver clean, accurate cuts. •
A material guide adjusts for the material height. The minimum material height is 1/2" and the maximum material height is 2". The material guide is easy to set. Have the workpiece ready to slip in, loosen the set screws, slip the workpiece below the material guide (leaving 1/16" space between the workpiece and the material guide), and tighten the set screws. •
Stacker arms adjust for material thickness. The minimum material thickness is 3/8" and the maximum material thickness is 7/8". •
The indexing system is accessed through the end panel and can readily calibrate to the required spacing. •
In dual-cut mode, the maximum depth of cut with the bottom blade is 3/8". (With the back blade removed, the maximum depth of cut with the bottom blade is 1-1/2".) The maximum depth of cut with the back blade is 1/2" (dual- or single-cut). The depth of cut is set by using the hand wheels at the back of the machine. •
Drive rollers feed the workpiece through the machine. The material length is unlimited as long as you support the material that extends beyond the machine. •
The aluminum surface is enhanced with slip plastic to improve material-feed through the machine. The center cylinder clamps the workpiece in place while the cuts are being made. •
A roller is used to activate the indexing system while moving the workpiece through the machine. The spacing on the workpiece is set from the leading edge of the block to the leading edge of the next block. The maximum spacing is 3". •
The width of the cut is determined by the tooling. The machine can accept tooling up to 3/4". •
The average speed is three feet per minute (based on two cuts, one inch spacing). The Dentil Molding Machine's footprint is 46" x 33". The machine requires a 110 volt power supply and a clean compressed air supply (80 pounds minimum). The shipping weight is 900 pounds (freight class 65). The Dentil Molding Machine has a dust collection box which must be attached to a 4" dust collecting system. •
Call (801)498-7891
Details: SPECIFICATIONS:
tooling: Skarpaz dado set (1/4 to 3/4") •
material height: ½" minimum to 2" maximum •
material thickness: 3/8" minimum to 7/8" maximum •
depth of horizontal cut (bottom blade): 3/8" maximum (1-1/2" when back blade is removed) •
depth of vertical cut (back blade): 1/2" maximum •
spacing: no minimum, 3" maximum •
width of cut: no minimum, 3/4" maximum (determined by tooling) •
average speed: 3 feet per minute •
floor space (footprint): 46" x 33" •
requires 110 volt power supply •
requires clean compressed air supply of 80 lbs minimum •
requires 4" dust collecting system •
Mirror Reflections is a Moulding Design Specialty Company. They sell DXF Files, Templates, and Knives for most moulders including Iida, Kentwood, Leadermac, Micron, Scmi, Silver, SK, Ultra, US Concepts, Wadkin, Weinig, ect. All drawings are designed on a CAD system by a service engineer/moulder operator with 26 years experience in the trade.
They have over 13,000 drawings in their state of the art database. 11,848 of these images are available online in their 100% to-scale profile catalog. Most orders for drawings, templates and knives from this catalog have less than 24-hour turnaround time to shipping. If you are an Architect, cabinet maker or a moulding producer looking for design ideas in mouldings, have a cnc template maker, or want to build your own custom profile catalog; their complete DXF library is available for immediate download. www.Mirror Reflections.com
Call (801)498-7891
Details: Images viewed from this website are the sole property of Mirror Reflections, Inc. and are intended solely for the purpose of our clients viewing. Any other misuse, including copying, archiving, or other forms of duplication or distribution are strictly prohibited.
5 products. Displaying 1 to 5.